收藏本站
SAW Components
SAW RF filter
B3905
315.00 MHz
Data sheet
ESD protection of SAW filters
SAW filters are E lectro S tatic D ischarge sensitive devices. To reduce the probability of damages
caused by ESD, special matching topologies have to be applied.
In general, “ESD matching” has to be ensured at that filter port, where electrostatic discharge is
expected.
Electrostatic discharges predominantly appear at the antenna input of RF receivers. Therefore
only the input matching of the SAW filter has to be designed to short circuit or to block the ESD
pulse.
Below three figures show recommended “ESD matching” topologies.
For wideband filters the high-pass ESD matching structure needs to be at least of 3 rd order to
ensure a proper matching for any impedance value of antenna and SAW filter input. The required
component values have to be determined from case to case.
Cs1
Cs3
Cs1
Cs3
Lp2
to output
matching
Lp2
to output
matching
Fig. 1 MLC varistor plus ESD matching
Fig. 2 Suppressor diode plus ESD matching
In cases where minor ESD occur, following simplified “ESD matching” topologies can be used
alternatively.
Cs1
Cs3
Lp2
to output
matching
Fig. 3 3 rd order high-pass structure for basic ESD protection
In all three figures the shunt inductor Lp2 could be replaced by a shorted microstrip with proper
length and width. If this configuration is possible depends on the operating frequency and
available pcb space.
Effectiveness of the applied ESD protection has to be checked according to relevant industry
standards or customer specific requirements
For further information, please refer to EPCOS Application report:
“ ESD protection for SAW filters ”.
This report can be found under www.epcos.com/rke.Click on “Applications Notes”.
Please read cautions and warnings and
important notes at the end of this document.
6
December 11, 2012
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
B39321B3961B210 FILTER SAW 315MHZ SMD
B39321R1921A310 RESONATORS 315MHZ
B39321R821H210 RESONATOR SAW CER 315MHZ SMD
B39321R822H210 RESONATOR SAW 319.508MHZ SMD
B39321R901H110 RESONATOR SAW 315MHZ SMD
B39321R903U410 RESONATOR SAW CER 315.5MHZ SMD
B39321R922H110 RESONATOR R 922 321.00MHZ
B39321R961H110 RESONATOR SAW 315MHZ SMD
相关代理商/技术参数
B39321B3961B210 功能描述:信号调节 315MHz 50ohms B3961 2.7dB 6V RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel
B39321R 822H210 制造商:TDK-EPC 功能描述:R 822 RESONATOR - Tape and Reel
B39321R 901H110 制造商:TDK-EPC 功能描述:R 901 RESONATOR - Tape and Reel
B39321R 903H110 制造商:TDK-EPC 功能描述:R 901 RESONATOR - Tape and Reel
B39321R 922H110 制造商:TDK-EPC 功能描述:RESONATOR R 922 321.00MHZ - Tape and Reel
B39321R 951U410 制造商:TDK Epcos 功能描述:R 951 RESONATOR - Tape and Reel
B39321R 961H110 制造商:TDK-EPC 功能描述:DCC6C RESONATOR - Tape and Reel
B39321R 981U410 制造商:TDK-EPC 功能描述:DCC6C RESONATOR - Tape and Reel